How to Know What Size Base is Needed

Measure the circumference of the bottom of the shaft before it engages the base. To size the base, the best way is to tape a piece of string to one side of the shaft, go all the way around the circle. The length of the string is the circumference of the bottom of the shaft.  The formula is the length x 3.14 which equals the diameter. The hole should be 1/4" larger than the shaft diameter.  Select from the standard models below or order custom sized.

 All About Tuscan Bases

Tuscan Bases are used with the classical Order of Tuscan created by the Etruscans (6th Century BC). They have one rounded profile (Torus) that sits on a square (Plinth)  Imperial Productions® offers them Load Bearing made from exterior hardwood staves glued together as done for the past 200 years. Select from exterior woods White Pine, White Oak, Western Red Cedar. The maximum diameter of the Torus is 36" (91.44cm) with any size of Plinth. Order 1 or 2 parts to any custom size and even parts of the column shaft that may be rotted.

Decorative Tuscan Bases are hollow and do not hold load. They envelop a load bearing plug or the column shaft that supports the column's weight. All are made from molds available split or whole. They are made from ArchPolymerTM  which is rot water and insect resistant for interior & exterior use, GRG-NeoPlasterTM for interior use and GFRC-ZeamentTM a Portland Cement composite for commercial or high traffic areas.

 SPLIT BASES FOR COLUMN  WRAPS

All of our bases can be ordered split for column wrap. ArchPolymerTM bases can be split down the middle or on the diagonal. You will loose the thickness of the blade once cut. Always use the approved adhesive and poly spackling compound to cover the seam. For GFRC-ZeamentTM we recommend ordering them precut, however if you cut them yourself we suggest a diamond blade.

 Issue: The bases of the columns are rotted and need to be replaced 

 Solution: an Economical Approach for non National Trust Buildings

The traditional base is solid wood and holds the load of the column shaft. For historic buildings we can create exact reproductions. For average homes where there are economic constraints, you can order a white oak a load bearing plug to hold the shaft weight and cover it with one of our composite bases split to encapsulate the load bearing plug. The hole size of the decorative base should be slightly larger than your load bearing plug accounting for the thickness of the blade if you have to cut the base in half to wrap the plug.  

 DOWNLOAD & AUTOFILL FORM

Select from 24 solid Hardwoods to create exact Historic Duplications of existing Bases with micro precision. Order them Whole or Split.

<= Click the PDF Form

 Fill in Measurements and Specify the Hardwood

 send the form by email to 

 sales@imperialproductions.com

 See wood treatment article to extend wood life

 CUSTOM COMPOSITE

Composites are created with new molds. These hollow Tuscan Bases serve as decorative elements to wrap load bearing posts

Select from the following Materials

 ArchPolymerTM a lite weight synthetic wood Interior & Exterior

 GRG-NeoPlasterTM - A gypsum based Composite for interior use

 GFRC-ZeamentTM- A concrete based Composite for exterior use

<= Click the PDF Form

 Fill in Measurements and Specify the Material

Custom Bases are priced as per mold charge and

number of units required

 send the form by email to 

 sales@imperialproductions.com

 click for Non Wood Tuscan Custom Page

 FAST TRACK: 42 Models on this Page - Click Size Range

 Looking for

 Square Bases

 Click here

  A) Hole or Flat 4" to 6-7/8"

 1 of 45

 Torus Top Flat Round Diameter 4-1/4"

 Fits Column 4" Diameter = Circumference 12-1/2"

  * All Prices, Exchange and Specifications Subject to Change without Notice  E&OE

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 2 of 45

 Torus Top Flat Round Diameter 5-1/4"

 Fits Column 5" Diameter = Circumference 15.7"

  * All Prices, Exchange and Specifications Subject to Change without Notice  E&OE

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

  Item 3)  Hole Fits 5-11/16" column  

Buy Options

      Materials

IPTB6-BASE is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 5-11/16" round column (approximately 5-13/16" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

  Item 4)  Hole Fits 6" column  

Buy Options

      Materials

IPTB500-BASE is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 6" round column (approximately 6-1/8" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

  Item 3)  Hole 6-1/4" (15.8)  

Buy Options

      Materials

IPTB301-BASE is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 6" round column (approximately 6-1/4" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 6 of 45

 Torus Top Flat Round Diameter 6-1/4"

 Fits Column 6" Diameter = Circumference 18.85"

  * All Prices, Exchange and Specifications Subject to Change without Notice  E&OE

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

Buy Options

      Materials

  B) Hole or Flat 7" to 8-7/8"

  Item 8)  Hole Fits 7-5/8" column  

Buy Options

      Materials

IPTB8 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 7-5/8" round column (approximately 7-3/4" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 9 of 45

 Hole 7-3/4"

 Fits Column 7-1/2" Diameter = Circumference 23.56"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  E&OE

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 10 of 45

 Hole 8-1/8"

 Fits Column 7-3/4" Diameter = Circumference 24.34"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  E&OE

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

  Item 11)  Hole Fits 8" column  

Buy Options

      Materials

IPTB300-BASE is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 8" round column (approximately 8-1/4" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 12 of 45

 Hole 8-1/4"

 Fits Column 8" Diameter = Circumference 25.13"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  E&OE

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 13 of 45

 Torus Top Flat Round Diameter 8-1/4"

 Fits Column 8" Diameter = Circumference 25.13"

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

Buy Options

      Materials

 C) Hole or Flat 9" to 10-3/4"

 15 of 45

 Hole 9-1/2"

 Fits Column 9-1/4" Diameter = Circumference 29"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 16 of 45

 Hole 9-3/4"

 Fits Column 9-1/2" Diameter = Circumference 30.6"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

  Item 17)  Hole Fits 9-5/8" column  

Buy Options

      Materials

IPTB10 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 9-5/8" round column (approximately 9-3/4" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

  Item 18)  Hole Fits 10" column   

Buy Options

      Materials

IPTB503 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 10" round column (approximately 10-1/8" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a Portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 19 of 45

 Torus Top Flat Round Diameter 10-1/4"

 Fits Column 10" Diameter = Circumference 31.41"

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 20 of 45

 Hole 10-1/4"

 Fits Column 10" Diameter = Circumference 31.41"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

Buy Options

      Materials

    D) Hole or Flat 11" to 11-3/4"

  Item 22)  Hole Fits 11-5/8"(29.5cm) 

Buy Options

      Materials

IPTB12 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around an 11-5/8" round column (approximately 11-3/4" hole size)with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 23 of 45

 Hole 11-7/8"

 Fits Column 11-3/4" Diameter = Circumference 36.9"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

   E) Hole or Flat 12" to 13-7/8"

  Item 24)  Hole 12-1/8" (30.8cm)

Buy Options

      Materials

IPTB506-BASE is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 12" round column (approximately 12-1/8" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 25 of 45

 Torus Top Flat Round Diameter 12-1/4"

 Fits Column 12" Diameter = Circumference 37.7"

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 26 of 45

 Hole 12-1/4"

 Fits Column 12" Diameter = Circumference 37.7"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 27 of 45

 Hole 12-1/2"

 Fits Column 12-1/4" Diameter = Circumference 38.48"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

Buy Options

      Materials

  Item 29)  Hole Fits 13-5/8"(29.5cm)   

Buy Options

      Materials

IPTB14 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around an 13-5/8" round column (approximately 13-3/4" hole size)with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

    F) Hole or Flat 14" to 16-7/8"

 30 of 45

 Hole 14-3/16"

 Fits Column 14" Diameter = Circumference 44"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 31 of 45

 Hole 14-1/4"

 Fits Column 14" Diameter = Circumference 44"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 32 of 45

 Hole 14-1/4"

 Fits Column 14" Diameter = Circumference 44"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 33 of 45

 Torus Top Flat Round Diameter 14-1/4"

 Fits Column 14" Diameter = Circumference 44"

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

  Item 34)  Hole Fits 15-5/8"(39.6cm)  

Buy Options

      Materials

IPTB16-BASE is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around an 15-1/2" round column (approximately 15-5/8" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a Portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 35 of 45

 Hole 16-1/4"

 Fits Column 16" Diameter = Circumference 50.26"

    Options:  Materials  Factory Painted  Metal Coated  FireRated

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 36 of 45

 Torus Top Flat Round Diameter 16-1/4"

 Fits Column 16" Diameter = Circumference 50.26"

  * All Prices, Exchange and Specifications Subject to Change without Notice  

 * All designs & content copyrighted 2025 ImperialProductions® or Permissions Granted

 G) Hole or Flat 17" to 23-7/8"

  Item 37)  Hole Fits 17-1/2" column  

Buy Options

      Materials

IPTB18 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 17-1/2" round column (approximately 17-5/8" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

  Item 38)  Hole Fits 19-1/2" column 

Buy Options

      Materials

IPTB20 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 19-1/2" round column (approximately 19-3/4" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

  Item 39)  Hole Fits 21-1/2" column 

Buy Options

      Materials

IPTB22 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 21-1/2" round column (approximately 21-5/8" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

  Item 40)  Hole Fits 23-1/2" column   

Buy Options

      Materials

IPTB24 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 23-1/2" round column (approximately 23-5/8" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 H) Hole or Flat 24" to 36"

 42 of 45

 Hole 28"

 Fits Column 27-1/2" Diameter = Circumference 86.39"

  Item 43)  Hole Fits 30" column   

Buy Options

      Materials

IPTB30 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 30" round column (approximately 30-1/4" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

 44 of 45

 Hole 30" to 36"

  Item 45)  Hole Fits 36" column 

Buy Options

      Materials

IPTB36 is a simplified Tuscan Base molded as 1 piece (Round Torus & Square Plinth). The hole fits around a 36" round column (approximately 36-1/4" hole size) with the column's load residing on the substrate. The base does not hold load. It is available in ArchPolymerTM a lite weight composite material and optionally, GRG-NeoPlasterTM for interior fire rated applications and GFRC-ZeamentTM a portland cement composite for high traffic commercial applications. Customize by optional factory cuts. Specify Split for Pilaster up against a wall, Split for Post wrap, Wedged for an outside corners, Section cut for Wall Wraps - specify the size, Quartered for inside corners, or Engaged for portion cuts for Pilaster applications.  This base can be ordered FactoryPainted or components can be RealMetalCoated. 

  Tuscan Torus Base 36" to 10 Feet

    Base Info

 Moulding Wrap to Replace Broken Torus

For those that have a broken Torus here are two SuperWiggly ResinMold® casings. Remove the rotten round portion, provide us with the circumference of the existing Torus and apply your SupperWiggly ResinMold®

    Base Materials

 ArchPolymerTM

 is a synthetic wood, water

 rot and insect resistant 

 Material Properties ArchPolymerTM 

 click for  YouTube Video

 24 Hardwoods

  Fully Customizable &

  Historic Recreations

 click for  YouTube Video  

 PolyComp & FiberComp

 Calcium Carbonate & Fiberglass 

 Resins

 All Load Bearing

 Material Properties:

 FiberCompTM & PolyCompTM

 click  for  YouTube Video  

 Information

 Imperial Productions®

 Tuscan Bases sold in 16 Countries

 Tuscan Column Bases Toronto

 Tuscan Column Bases Montreal

 Tuscan Column Bases Calgary

 Tuscan Column Bases Vancouver

 Tuscan Column Bases Atlanta

 Tuscan Column Bases New York

 Tuscan Column Bases Chicago

 Tuscan Column Bases Miami

 Tuscan Column Bases Tampa

 Tuscan Column Bases Philadelphia

 Tuscan Column Bases Los Angeles

 Tuscan Column Bases Houston

 Tuscan Column Bases San Francisco

 Tuscan Column Bases New Orleans

 Tuscan Column Bases Denver

 Tuscan Column Bases Boston

 Tuscan Column Bases Mexico City

 Tuscan Column Bases Amsterdam

 Tuscan Column Bases London

 Tuscan Column Bases Sydney Australia

 Tuscan Column Bases Tokyo

 Tuscan Column Bases Paris

 Tuscan Column Bases Frankfurt

 Tuscan Column Bases Rome

 Tuscan Column Bases Dubai

 Tuscan Column Bases Bahamas

 Standard and custom Tuscan Bases are Perfect for new construction, home remodeling

 Commercial or historic retrofit

  How to Order Products  1-800-399-7585     +1-416-264-6096  

  email: sales@imperialproductions.com

  * All Prices & specifications in this website subject to change without notice

  * Prices are net, Freight, Taxes & Duties charged where applicable otherwise

        client is responsible for remittance

  * Measurements are approximate only, Final Product may vary from this website

   COPYRIGHT  MRDCI Martin Richards Design and Contracting Inc, Martin Richards DesignTM 

     and Imperial Productions®                                                        Feb 2018  all rights reserved

       Last Update: NOV-25